trunk/Arduino/libraries/DallasTemperature/examples/Tester/Tester.ino

@@ -8,7 +8,7 @@
 // Setup a oneWire instance to communicate with any OneWire devices (not just Maxim/Dallas temperature ICs)
 OneWire oneWire(ONE_WIRE_BUS);
 
-// Pass our oneWire reference to Dallas Temperature. 
+// Pass our oneWire reference to Dallas Temperature.
 DallasTemperature sensors(&oneWire);
 
 int numberOfDevices; // Number of temperature devices found
@@ -23,48 +23,48 @@ void setup(void)
 
   // Start up the library
   sensors.begin();
-  
+
   // Grab a count of devices on the wire
   numberOfDevices = sensors.getDeviceCount();
-  
+
   // locate devices on the bus
   Serial.print("Locating devices...");
-  
+
   Serial.print("Found ");
   Serial.print(numberOfDevices, DEC);
   Serial.println(" devices.");
 
   // report parasite power requirements
-  Serial.print("Parasite power is: "); 
+  Serial.print("Parasite power is: ");
   if (sensors.isParasitePowerMode()) Serial.println("ON");
   else Serial.println("OFF");
-  
+
   // Loop through each device, print out address
-  for(int i=0;i<numberOfDevices; i++)
+  for (int i = 0; i < numberOfDevices; i++)
   {
     // Search the wire for address
-    if(sensors.getAddress(tempDeviceAddress, i))
-	{
-		Serial.print("Found device ");
-		Serial.print(i, DEC);
-		Serial.print(" with address: ");
-		printAddress(tempDeviceAddress);
-		Serial.println();
-		
-		Serial.print("Setting resolution to ");
-		Serial.println(TEMPERATURE_PRECISION, DEC);
-		
-		// set the resolution to TEMPERATURE_PRECISION bit (Each Dallas/Maxim device is capable of several different resolutions)
-		sensors.setResolution(tempDeviceAddress, TEMPERATURE_PRECISION);
-		
-		Serial.print("Resolution actually set to: ");
-		Serial.print(sensors.getResolution(tempDeviceAddress), DEC); 
-		Serial.println();
-	}else{
-		Serial.print("Found ghost device at ");
-		Serial.print(i, DEC);
-		Serial.print(" but could not detect address. Check power and cabling");
-	}
+    if (sensors.getAddress(tempDeviceAddress, i))
+    {
+      Serial.print("Found device ");
+      Serial.print(i, DEC);
+      Serial.print(" with address: ");
+      printAddress(tempDeviceAddress);
+      Serial.println();
+
+      Serial.print("Setting resolution to ");
+      Serial.println(TEMPERATURE_PRECISION, DEC);
+
+      // set the resolution to TEMPERATURE_PRECISION bit (Each Dallas/Maxim device is capable of several different resolutions)
+      sensors.setResolution(tempDeviceAddress, TEMPERATURE_PRECISION);
+
+      Serial.print("Resolution actually set to: ");
+      Serial.print(sensors.getResolution(tempDeviceAddress), DEC);
+      Serial.println();
+    } else {
+      Serial.print("Found ghost device at ");
+      Serial.print(i, DEC);
+      Serial.print(" but could not detect address. Check power and cabling");
+    }
   }
 
 }
@@ -80,7 +80,7 @@ void printTemperature(DeviceAddress deviceAddress)
 
   // method 2 - faster
   float tempC = sensors.getTempC(deviceAddress);
-  if(tempC == DEVICE_DISCONNECTED_C) 
+  if (tempC == DEVICE_DISCONNECTED_C)
   {
     Serial.println("Error: Could not read temperature data");
     return;
@@ -92,29 +92,29 @@ void printTemperature(DeviceAddress deviceAddress)
 }
 
 void loop(void)
-{ 
-  // call sensors.requestTemperatures() to issue a global temperature 
+{
+  // call sensors.requestTemperatures() to issue a global temperature
   // request to all devices on the bus
   Serial.print("Requesting temperatures...");
   sensors.requestTemperatures(); // Send the command to get temperatures
   Serial.println("DONE");
-  
-  
+
+
   // Loop through each device, print out temperature data
-  for(int i=0;i<numberOfDevices; i++)
+  for (int i = 0; i < numberOfDevices; i++)
   {
     // Search the wire for address
-    if(sensors.getAddress(tempDeviceAddress, i))
-	{
-		// Output the device ID
-		Serial.print("Temperature for device: ");
-		Serial.println(i,DEC);
-		
-		// It responds almost immediately. Let's print out the data
-		printTemperature(tempDeviceAddress); // Use a simple function to print out the data
-	} 
-	//else ghost device! Check your power requirements and cabling
-	
+    if (sensors.getAddress(tempDeviceAddress, i))
+    {
+      // Output the device ID
+      Serial.print("Temperature for device: ");
+      Serial.println(i, DEC);
+
+      // It responds almost immediately. Let's print out the data
+      printTemperature(tempDeviceAddress); // Use a simple function to print out the data
+    }
+    //else ghost device! Check your power requirements and cabling
+
   }
 }